Downsizing To A Smaller Garden Pot Separation

The materials intended to fence your garden are not lacking. You can use wood, a lattice, brick walls, plant a natural hedge, and so on. At the moment, concrete is also very successful. And the sad gray concrete panels from before have made way for modern fence elements available in various patterns and formats.

The Mediation house proceeds are as follows: place concrete slabs between two posts. The number of plates depends on the height of the fence. The top concrete plate is generally of a different shape to ensure a beautiful finish of the whole, with for example a rounded.

Warning: the concrete plates are heavy. Wear protective clothing, shoes and gloves and be careful not to hurt yourself as you slide the plate between the posts. here below are some step explaining about Downsizing to a Smaller Garden Post Separation.

Step 1: Measure the terrain
Determine the location of the fence and mark the terrain with demarcation poles.
Measure the length of the fence to determine the number of concrete slabs and intermediate studs you need.
Also, check that the seat is flat. Either add or remove soil.

Step 2: Place the corner post

At one of the corners of the fence, dig a hole 50cm deep.
Place the corner post into the hole, fill this hole with dry concrete (1 serving of cement for 3 servings of sand/gravel) and do not forget to do it.

Check that the post is square and secure it with cleats. Make sure they are not in the way …
Depending on the construction, two walls can go in different directions from this post. Make the count. If only one wall is used, for aesthetic reasons, avoid placing a post with two grooves.

Step 3: Place the profiles

Place a wooden profile at a sufficient distance from the first corner post. With two cleats, hold the profile in place.

Tension three tensioning cords between the profile and the corner post that will serve as a guide for laying the concrete slabs and the rest of the posts. The height of the first tensioning cord depends on the width of the concrete slab you are using. The distance between the different tensioning cords must always be the same, p. ex. 40cm everywhere.

If a second wall comes to rest on the first intermediate post, also place for this purpose a wooden profile with a tensioning cord.
If the fence is not too long, you can also directly place the last corner posts, instead of the wooden profiles, to fix the tensioning cord.

Step 4: Place the concrete slabs

Dig a hole for the second intermediate post at a distance equal to the length of the concrete plate in relation to the corner post.
Insert the first concrete plate into the groove of the corner post and let it slide to the ground.
Then level the second intermediate post, ensuring a good connection with the lower concrete plate.
Check that the post is level and at a good height.
Fill the dry concrete hole and lay it properly.
Proceed in the same way for the rest of the fence, placing the lower concrete plate each time only.
Make sure that the concrete slabs are well placed to the lower end of the stud slits.
Remove the wooden profile and replace it with the last corner post.
If you have to saw the last custom concrete slab, use an angle grinder with a diamond disc.
After grinding the concrete plates, it is possible that they do not fit easily into the groove of the corner post. In this case, you can grind the edges slightly bevel.

Step 5: Place the top finish plates

Before placing the other concrete slabs between the intermediate posts, wait a day.
Once you have placed 3 or 4 plates, finish with the last finishing plates that usually have another shape.
To be able to place these top plates easily, scaffolding is not a luxury. It is even recommended to work with 2 or even 3 people. Concrete slabs are relatively heavy, especially if you have to lift them over your head.

Step 6: Work in steps

Not all gardens are as flat as a pool table. It is best to adapt your fence to the relief of it and not the other way around.
In order for the concrete fence to conform perfectly to the seat, make a cut in the lower concrete slab of the lowest part of the wall.
Height differences should not be too large. For a comfortable transition, it is necessary to count 10 to 15cm of height difference in stages.

Step 7: Fix and make the joints

With a hammer, insert small wooden wedges between each concrete slab and the intermediate studs. First, pull the concrete slab on one side and make sure it is well placed between the posts.
Now realize the vertical joints at the posts.